Відео

Do you have the schematic for this? Thanks!

Thank you very much, finally a video of this type that leaves the files in 3D. Greetings from Chile

but theres no drainage holes for the plant

I want to buy a kit, but I'm unable to ship to the US off your website. Can you please advise?

Just finished this project and it works well ... as long as it is plugged in. Once disconnected and repowered, it does not correct itself to the current time. It displays the time when disconnected and then goes forward from there. I have checked the wiring twice, replaced three DS3231 units and replaced the battery to no avail. Both batteries are new and measured 3VDC. The required libraries are installed and current. I verified the code is the same between the Electromaker website and my IDE. I’m missing something. Any help will be appreciated. Thank you.

why not use esp32 ?

Very well done..thank you

Thanks, Lewis, for the video. Are the laser cut files on Etsy as well?

Curious as to how long will this operate on full chrage? Thanks!

Liked and subscribed for the timing belt assembly

Arduino nano codes please...

Share me code

Firstly and fore mostly: thank you. Been trying to get a GC9A01 round LCD to work with a logic level shifter and couldn't get it to work. Pulling OE high as per your video worked first time. Thank you :)

Can I replace the 18650 Lithium Ion Batteries with rechargeable AA Batteries?

I love it ❤❤❤😊🎉

'IÎÌiFi génie

Nice - of course it would be even cooler if the mirror was a touchscreen (I know that that is probably either super expensive and/or hard to accomplish!) and if it could do seamless change-over between two of them (so say you are listening to the news while brushing your teeth in the bathroom and leave to put on clothes in the bedroom and the bedroom mirror seamlessly plays the news there) :) I also don't like (note: I know, for someone who is not actually DIYing much, I sure "complain" a lot!) that you covered up so many cables (and the LEDs - can't easily replace them if they were to go bad, which does happen!) etc. (it will make upgrading/changing this thing way harder)...then again, visible cables never annoyed me! I frankly think people who always try to hide cables are strange!

Is it possible to crimp two wires into one connector to make a Y-split?

You just got me a possible new obsession 😂

Hi mate I’m in the uk, just find your channel it’s great, after I download the file to print is it possible to make it deeper ? Could you please make the frame 80mm and even I can make a donation, can I please get your email address

brilliant

what font did you use for the signs in fusion 360?

that's awesome!

Could I use tcrt5000 as analog input like potantiometer?

After watching this video 2-1/2 time I was able to crimp all six end points of my custom 3-core cable in one go. How good is this video 🙂

How to compile C file arduino uno project?

Hi there, I would like to purchase your diy kit. But how can I customise it to use a 10" speaker?

hi great tutorial! i would like to make are large version of this - is it possible to upscale it 2m x 2m sizing or even 3m? and how long would it take to create a drawing of this size? and can you use natural sand with it also rather than craft sand?

Subbed thank you 👍

Can you speak Arabic, man, and explain to us without songs, you idiot?🤪

Hi, It´s amazing proyect!!!, I have a question, if i wish to add two push buttons to open and close curtains without internet, how do you do it?, Thanks

I had no idea you could make such a high quality product, I'm really surprised! In fact, we specialize in producing this kind of waterproof magic mirror, but you DIYed it, which is really cool!😮

Thanks

Oh I'm definitely trying this out. The look awesome

💕👍

Can you by any chance sell me all the components printed and shipped at my housenin greece it ll be for sure cheaper than printing them here......if u can let me know plz i really like it

very nice , from argentina ¡¡¡¡

Hello mate, I know that you posted the video ages ago but I'm planning on building my own rendition of your arduino bartender. I've noticed that the stl file for the drag chain isn't up on Thingiverse with the rest of the components. Was just wondering if you would be able to fix this at some stage?

How how much will it cost me if I need the 3d printed standout and the covers and also shipping

Very helpful. But which size jaw opening should I use for the Dupont terminals seen in the video ? Does it depend on the wire size ? If so, where can I find a chart to match them ?

Is it okay to the TRCT 5000 IR SENSOR Module to ESP 32?

This Idea is excellent. I haven't checked the video yet, but with a quick scan in the transcript, it looks like it might benefit an NTP synchro. Also, it might be a good idea to follow the correct data path for the data only, and use a parallel path for the power lines, to reduce the power losses in the strips.

I've always used multitouch foil for mirrors and coffee tables. Also used mini PCs instead of Raspberry Pi too. More responsive and more capable, but of course more expensive. This really is INCREDIBLY clean and professional. Beautiful project.

عمل رائع

What size of the wire is?

can anyone tell me what sand i should use? i am trying to find some in the UK

Amazing,fantastic,meditative!

this is so cool I want to build it at some point

Can you make a new version of your 2 d plotter

The amount of power supply in terms of voltage and current